How to use T-Box

Automatic memory scanning function(If there is a new definition, after scanning, the memory will be stored, then when scan the same mobile phone at the second time, the device will identify it automatically and scan definition rapidly in 1 second)after scanning done the software platform will pop-up automatically .using the Philips chip can make the time shorted to 3-20 seconds when scanning the SPD chip and USB circuit(even for the special mobile phone only need less than 50 seconds),super fast and super accurate. Can be defined by manual control as : RXD, TXD, USB D+, USB D-, VCC, GND signal lines and so on,the master interface as following: The latest optimal power circuit, the super short-circuit & overcurrent protection

• 1.There is a overcurrent protection both in power clip and output socket ;the box scanning power supply is automatic conversion, no need distinguish Positive and negative for charging mobile phone.
• 2. Prompts from speaker and LED when short-circuit and overcurrent.
• 3.There is a reset key in T BOX to power off mobile phone, It is quite convenient for SPD mobile phone to do the operation of reading and writing etc.(There are full details in the software platform specification)

NEW: The latest and perfect SPD&MTK software platform can help you write flash, format, read lock(include SPD mobile phone user lock) , read phonbook, write IMEI, repair BAD fault. The platform as following:

Support these types of chips which as following:

MTK, SPD, Ankai, ADI, SKY, TI, INF, AGERE, OM, SI(4904) etc.. Scan these chips and BOOT signal automatically, we can upgrade the master for scanning the unknown chips, the scanning speed is supper fast and accurate.

NEW: All intelligent operation &human design

• 1. Identify cable no need manual control, applicable for any cables from other factories.
• 2. Identify chips by scanning automatically (not suggest because of the slow speed, time from 2second to 6 minutes).
• 3. Scan BOOT signal automatically, no need to press the power-on key of mobile phone when scanning the SPD chip(just need to press the "reset" key to power off when doing the "write" and "read" operation.
• 3. The software platform will pop-up after the scanning done.

Scan USB explanation of scanning master:

After open T BOX master software, connect to the mobile phone, then power the mobile phone by the power line of the conversion lines which need to be connected to the BOX, select the types of chips which you want to scan(Take scan the definition of SPD USB for example: 6600D CPU no need to scan USB) the operation description will appear automatically in the master interface .As following:

The dialog will pup-up, please click "ok" after confirm your connection is correct, then the master software start to scan(press the power-on key of mobile phone when scanning chips until done, but except SPD, please read carefully to learn more details from the dialog of the mast software. As following It takes 3-10 seconds to scan the definition of MTK normally, and scanning the definition of MTK needs 10-30 second, the related will pop-up automatically after scanning done. As following Description of SPD platform: NOTE :All the functions can be used only after the definition scanning of mobile phone done.When scan the new chips, such as SPD6600MSPD6600M, E, H, R, I, after the "scan USB" scanning done, the prompt from remind you new hardware found and install the mobile phone driver which saved in T BOX program installation list (X:\T-BOX\drivers\phone\SPD SC6600M USB driver)after driver has been installed, there will be a new COM in the computer device manager ,please select the new COM when reading SPD CUP. The following picture shows how to use the functions of the software which can be used ony after the definition scanning of mobile done. Specification of reading:(please press the red bottom of the BOX which called "reset key" before reading SPD every time) after click the "read" bottom the related dialog will pop-up to prompt you to input the name of mobile phone which you want to scan, then the software will read automatically(please remember backup the details of the mobile in order to prevent accidents)As following: Note: all the function of the platform can be used only after the definition scanning of mobile phone done.
Functions of finding password and user lock: (please press the red key which called "reset key" of the box before operate every time),first read the information of the mobile phone which was locked, then click "Analyze", the dialog will pup-up to prompt you to transfer the information locked, the power-on password and user lock will be analyzed automatically. Note: all the function of the platform can be used only after the definition scanning of mobile phone done.
Description of "write": (please press the red key which called "reset key" of the box before operate every time)after click "write" the dialog will pup-up, input the information which you want to write, the software can unlock the locked information and write the information automatically .As following Description of "Format": Note: all the function of the platform can be used only after the definition scanning of mobile phone done. After you open the platform, there are two options of flash which are "manual" and "HAND", you can select one type that fix your mobile phone, it will format automatically if you don't select any. As following: Description of rewrite IMET: If just rewrite IMET, please read flash first, then input the IMEI and tick "set IMET" as this: just input IMET1 if there is only one IMET in your mobile phone, click "write" for writing IMEI, then it will pup-up a dialog please click "Y" after you confirm the IMET is correct. (Note: when writing the IMET of SPD need to write flash at the same time.)As following: The method of rewrite IMEI is the same as write flash, as following: Write IMEI done, as following:

Description of MTK chips scanning and operations of software platform:

After open T BOX master software, connect to the mobile phone, then power the mobile phone by the power line of the conversion lines which need to be connected to the BOX, select the chips that you want to scan (take scanning MTK for example as following),click"Scan Rx.Tx",the master interface will appear the description of the operation automatically .As following: After select the types of chips, a dialog will pop-up, please click "ok" after you have confirm the selection is correct, the scanning will be done automatically (the time of scanning MTK needs 1-10 seconds),please keep pressing the power-on key of mobile phone until the scanning done(otherwise the operation will be fail).As following: The related platform will pup-up after the scanning done .As following: Note: all the function of the platform can be used only after the definition scanning of mobile phone done. The settings of the software platform :after click "read", it will prompt you to press the power-on key of mobile phone.(Note: please press the red key which called "reset key" of the box after every operation done, it can power off the mobile phone and get ready for your next operation.)As following: After press the "reset key" then keep pressing the power-on key, if the communication is normal it will appear the progress reports which the words in green then needn't press the power-on key, all the information of flash will appear in the interface. As following: After reading done, the dialog will pop-up to prompt you to save the mobile phone information, you just need to select a path to save it according the name of your mobile phone. As following: Following is the Description of write flash: click here to transfer the information which you want to write, the software will analyze it automatically. As following: Note: All the functions can be used only after the definition scanning of mobile phone done. After make sure the information is correct then it will prompt you to press the power-on key of your mobile phone, as following: After press the "reset key" then keep pressing the power-on key, if the communication is normal it will appear the progress reports which the words in green then needn't press the power-on key, the software can unlock and write flash automatically, as following: After writing done, the platform will show the related information, as following: Note: all the function of the platform can be used only after the definition scanning of mobile phone done. Following is the function of "Unloc Anys"(can help user to read phone book).transfer the information to be analyzed, tick and then click "Anyl File" as following: Note: all the function of the platform can be used only after the definition scanning of mobile phone done. Following is the operation of "Unlock", click "Unlock",follow the prompt of keeping pressing the power-on key of mobile phone, as following. After press the "reset key" then keep pressing the power-on key, if the communication is normal it will appear the related information and the unlock code as following: Note: all the function of the platform can be used only after the definition scanning of mobile phone done. Following is the operation of IMEI rewrite, just input the IMEI, also for the dual IMEI Click "SN1 CHG" to write IMEI needn't to press the power-on key, this operation will be done automatically.